Jim Dunlop Strap Grommet Black

Jim Dunlop Bridge Pin Black - Sell Per Pin

Dunlop Mesh Straps are made from soft, comfortable fabric in rich, dark colors.

Jim Dunlop Bridge Pin White - Sell Per Pin

This pedal provides a huge, responsive range of gritty and textured tones that enhance the sound of your rig while preserving its fundamental character-and in an MXR mini housing, this pedal will free up some serious pedalboard space.This pedal can be powered by a Dunlop ECB003 9-volt adapter, or the DC Brick™, Iso-Brick™, and Mini Iso-Brick™ power suppliesInput Impedance 400 kΩOutput Impedance* 1 kΩNoise Floor* -115 dBVGain 3 dBV to 43 dBVBypass True HardwireCurrent Draw 2.2 mAPower Supply 9 volts DC

The Bass Compressor provides recording-quality compression with Constant Headroom Technology and true bypass switching for keeping your low end tight and clean.This pedal can be powered by a 9-volt battery, a Dunlop ECB003 9-volt adapter, or the DC Brick, Iso-Brick, and Mini Iso-Brick power supplies (not included).Directions:Run a cable from your bass to the Bass Compressor's INPUT jack and run another cable from the Bass Compressor's OUTPUT jack to your amplifier.Set RELEASE, ATTACK, OUTPUT and INPUT controls to 12 o'clock and the RATIO control to 4.Turn the effect on by depressing the footswitch.Observe the METER display while playing normally and set the INPUT knob so that the first 3 to 7 green gain reduction LEDs light, clockwise to light more and counterclockwise to light less LEDs.Rotate the OUTPUT knob clockwise to increase overall effect volume or counterclockwise to decrease it.Rotate the ATTACK knob clockwise to increase reaction time of compression or counterclockwise to de…

The Slash Octave Fuzz combines searing fuzz with a sub octave grow and an array of controls for fine-tuning your sinister sound.This pedal can be powered by a 9-volt battery, a Dunlop ECB003 9-volt adapter, or the DC Brick™, Iso-Brick™, and Mini Iso-Brick™ power supplies (not included).Input Impedance 47 kΩOutput Impedance 100 ΩSignal to Noise* >85 dBDry Max Gain +1.6 dBFuzz Gain Range 40 dBOctave Up Gain Range 20 dBSub Octave Corner Freq. 149 HzBypass True HardwireCurrent Draw 17 mAPower Requirement 9 volts DC

The Bass D.I.+ features a D.I., separate clean and distortion channels, an array of controls to fine-tune your sound, and a noise gate trigger control to eliminate hum and hiss.This pedal can be powered by a 9-volt battery, a Dunlop ECB003 9-volt adapter, or the DC Brick™, Iso-Brick™, and Mini Iso-Brick™ power supplies (not included).Input Impedance 2.2 MΩOutput ImpedanceUnbalanced 150 ΩBalanced 300 ΩBypass Freq. Response+0/-0.5 dB, 20 Hz to 20 kHzTone ControlsBass ±18 dB, 60 HzMid ±10 dB, 850 HzTreble ±12 dB, 4 kHzNoise Floor*Bypass -102 dBVClean Effect -98 dBVDistortion Effect, Gate Off -94 dBVDistortion Effect, Gate On -98 dBVVolume Control Range 40 dBGate Trigger Range 28 dBSensitivity -66 dBV at 1 kHzBypass BufferedCurrent Draw 9 mAPower Supply 9 volts DC

The Distortion III delivers everything from sweet singing overdrive to massive distortion crunch. This pedal can be powered by a 9-volt battery, a Dunlop ECB003 9-volt adapter, or the DC Brick™, Iso-Brick™, and Mini Iso-Brick™ power supplies (not included). Input Impedance 1 MΩOutput Impedance* 5.5 kΩNominal Intput Level -22 dBVMaximum Output Level +3 dBVNoise Floor** 84 dBVTone Control ±6.5 dB at 3 kHzDistortion Gain 22 dB to 50 dB, 1 kHzBypass True Hardwire Current Draw 3.5 mAPower Supply 9 Volts DC

The Micro Amp allows you to boost your signal with a preset amount of gain up to +26dB.This pedal can be powered by a 9-volt battery, a Dunlop ECB003 9-volt adapter, or the DC Brick, Iso-Brick, and Mini Iso-Brick power supplies (not included).Directions:Run a cable from your guitar to the Micro Amp's INPUT jack and run another cable from the Micro Amp's OUTPUT jack to your amplifier.Start with the control at 12 o'clock.Turn the effect on by depressing the footswitch.Rotate the GAIN knob clockwise to increase amount of signal boost or counterclockwise to decrease it.Input Impedance 1 MΩOutput Impedance 470 ΩMaximum Output Level +6 dBVNoise Floor* -80 dBVGain Control +0.5 dB to +26 dBFreq. Response 20 Hz to 20 kHz,+0 dB, -1.4 dBBypass HardwireCurrent Draw 2.5 mAPower Supply 9 volts DC

The Carbon Copy Analog Delay delivers rich, warm bucket-bridgade delay with up to 600ms of delay time and modulation.This pedal can be powered by a 9-volt battery, a Dunlop ECB003 9-volt adapter, or the DC Brick™, Iso-Brick™, and Mini Iso-Brick™ power supplies (not included).Input Impedance 1 MΩOutput Impedance 1 kΩMax Input Level +5 dBV at 500 HzMax Output Level +8 dBVNoise Floor*Mix at Max CW -96 dBVMix at Max CCW -104 dBVDelay Distortion